Simple Silver Logo
60 day money-back
Guaranteed
Simple Silver Logo
60 day money-back
Guaranteed
Simple Silver Logo
60 day money-back
Guaranteed
Simple Silver Logo
60 day money-back
Guaranteed
Simple Silver Logo
60 day money-back
Guaranteed
Simple Silver Logo
60 day money-back
Guaranteed

Troubleshooting

1. Health & Safety

Water balancing & treatment is a three-fold process

All three processes must align to provide pristine clean water.

1. Water Balancing

  • simplesilver™ automatically balances the waters pH, alkalinity, total dissolved solids, scale & corrosion.

Note: Since 2003, simplesilver™ has been assessed by AsureQuality for safety as a hot tub water balancer.

2. Water Treatment

  • A small amount of chlorine must be added after use to comply with local & government guidelines to control the bacterial levels.

3. Filtration

  • The filter pump circulates the water through filters removing any skin, perspiration, oils, lotions, hair, water salts, dust, dirt & any other foreign matter, helping simplesilver™ maintain the water quality, condition & clarity.

Note: It is critical that your filters are cleaned at least every two weeks using a filter santising solution, as water alone is ineffective & will not clean these.

NO!

DO NOT USE YOUR HOT TUB IF THE WATER IS NOT CRYSTAL CLEAR - IF IT'S CLOUDY - HAS A GREEN TINGE - HAS AN ODOUR.

  • These issues are an indication that bacteria or fungus is present in the water & this could be detrimental to your health, skin & well-being.
  • Please refer to our troubleshooting section numbers 3.1 to 3.6 below, for a solution to rectify your problem.

2. General Issues

  • Generally when the sides of the hot tub feel slippery this is due to a build-up of skin, oils & perspiration, similar to when you have a bath.
  • Remove the filters & clean these using a filter sanitising solution as water alone is ineffective & cannot break these down.
  • While the filters are removed, with a cloth & a bucket of water (to rinse the cloth), clean the insides of the filter cavity & housing. This area is commonly overlooked & may have a build-up of skin, perspiration, oils & lotions & can be a cause of unpleasant odours & slippery sides. It is very important to clean this area each time the filters are cleaned & replaced.
  • Make sure the filters are dry before reintroducing these as the filter fibres will expand making them more effective.
  • Dry filters also stops the water from foaming.
  • With clean filters in the hot tub, operate all pumps manually a few times to quickly remove any other contaminates within the water & with a cloth wipe the sides of the hot tub walls above the waterline.
  • Air has become entrapped in the simplesilver™ bag that contains the minerals.
  1. You will need to take out the simplesilver™ bag from the plastic tablet by removing the back cover.
  2. Use a blunt knife & carefully prise off the cover, making sure not to tear the bag that contains the simplesilver™ minerals.
  3. Remove the simplesilver™ bag.
  4. Put the bag in the hot tub water & gently massage it to break up any minerals that may have stuck together.
  5. Then gently squeeze the bag to expel any entrapped air, this will stop the tablet floating.
  6. With the bag still under water, carefully reinsert it back into the plastic tablet container & reattach the back cover.
  • Then place the simplesilver™ tablet in your preferred location in the hot tub water.
  • Foaming in the water may happen after cleaning your filters with a filter sanitising solution & installing these while still wet.
  • We recommend that you dry the filters after cleaning & prior to reinstalling.
  • This should stop the foaming process & it will also make the filters more efficient as the filter fibres will expand when dry.
  • To make life easier, purchase a second set of filters & swap these over at least every two weeks.
  • This is most likely due to the filters containing an abundance of skin, perspiration, oils & lotions. Please clean the filters using a filter santising solution, as water alone is ineffective & cannot break these down.
  • While the filters are removed, with a cloth & a bucket of water (to rinse the cloth), clean the insides of the filter cavity & housing.
  • This area is commonly overlooked & may have a build-up of skin, perspiration, oils & lotions & can be a cause of unpleasant odours & slippery sides.
  • It is very important to clean this area each time the filters are cleaned & replaced.
  • Bacteria & fungus may also reside on the underside of the insulated cover, zips & headrests that are not in the water, therefore cannot be treated. Please remove the headrests, clean these & the insulated cover & zips with diluted bleach or chlorine solution to remove any contamination.
  • Make sure that the water jets are not ejecting water onto the underside of the insulated cover, as this will encourage bacteria & fungus growth.

3. My hot tub water is not crystal-clear

The water is - cloudy - grey - has an odour

  • As a reference, your hot tub water "Should Always Look Like This" when using simplesilver.
  • There are various issues that can cause the hot tub water to become cloudy - grey - smelly.

Check the following settings

  • In the majority of cases this is due to an insufficient flow of water over the simplesilver™ tablet. Are you confident the filter pump has been set correctly to circulate 100,000 litres per day?
  • This flow rate is critical as it releases the correct amount of simplesilver™ minerals at a constant & controlled rate to balance the hot tub water. If not, the water will not be pristine. Click here, "Controller Settings" for more information.
  • Filters play a critical role, are the filters blocked? If so, this restricts the water flow & limits the correct amount of simplesilver™ minerals that are released into the water to balance it.
  • To find out more click here, "How do I test if my filters are blocked" & "Why do I need to clean my filters & why are these vitally important".
  • If Bromine was previously used, then the water needs to be drained prior to starting Step 1 - Installation Process "click here for Getting Started Information".

Other important settings to check

  • Is the filter pump controller set on automatic mode?
  • Is the sleep mode turned off?
  • Is the holiday mode turned off?
  • Is the power saving mode turned off?
  • Are all jet nozzles fully open & if you have one, is there a small amount of water circulating out of the fountain ?
  • Is the filter box flap opening fully & not restricting the water when the filter circulation pump operates?

If any of the above settings were incorrect & have now been adjusted

  • It will take 3 days for the water to be correctly balanced & the issues resolved.
  • Do not use the hot tub over this period.
  • After day 3, if the water is pristine - enjoy the hot tub, no further action is needed.
  • If not, follow the instructions below.

Once you are confident the settings are correct - It will be a calcium carbonate (scale) issue

  • This is due to a build-up of calcium carbonate (scale) & other water salts within the system. Similar to the scale you sometimes get in your kettle.

Note - If you have a new hot tub, there will be no scale build-up, please refer to "Troubleshooting 3.2" to resolve your issue.

So what's caused this?

  • The formation of scale is due to various factors such as hard water &/or substandard maintenance or previous water treatments.
  • After 4 to 6 weeks simplesilver™ slowly softens any scale within the system. This is then detached & removed by the water passing over the softened scale. These salts are held transparently within the hot tub water, then removed via the filters & you cleaning these.
  • If the hot tub has an abundance of scale, the scale salts bond together & come out of transparent solution, turning the water grey & smelly. Once again these are then removed by your filters & you cleaning these.
  • Depending on the volume of contamination, it will take time for each layer of scale to soften & detach.
  • Once all the scale is removed & the system is clean, simplesilver™ then coats the insides of the hot tub to limit any further build-up of scale.

Now Follow - Solution 1 - Scale Cleaning Process

For a printable version click here: Solution 1 - Scale Cleaning Process

Cleaning Process

  1. Purchase a small container of hot tub chlorine granules.
  2. Add 120 grams (half a cup) of chlorine granules into a container of warm water.
  3. Mix until the chlorine granules are dissolved.
  4. Pour the diluted chlorinated water into the hot tub water.
  5. Operate all pumps for 1 hour so the water & chlorine is circulated throughout the entire system.
  6. Note - you will need to manually activate the pumps that have an auto-off function over this period to ensure that there is continuous water flow.
  7. Drain a third of the hot tub water.

Re-filling Process

  1. Re-fill the hot tub to the recommended water level. Note - draining more will also remove the simplesilver™ minerals & their effectiveness.
  2. Set the filtration timer on the controller. Go to the "Controller Settings" section & follow the instructions for your model controller.
  3. Ensure your controller is set to circulate 100,000 litres of water daily.
  4. Do not use the hot tub for 3 days. If you use the hot tub before this, there will not be sufficient simplesilver™ minerals released into the water to balance it.
  5. After day 3, once the water is crystal-clear & odourless, you can start using the hot tub again. Remember to add a small amount of chlorine after use to comply with local & government guidelines to control the bacterial levels.

Important

  • By removing a third of the water & replenishing it with new water will dilute the level of scale within the water.
  • Remember, if you remove more than a third, you will also remove the simplesilver™ minerals & their effectiveness to balance the water.
  • simplesilver™ continually softens & removes any remaining scale over time. This is a slow process & will depend on the amount of scale within the hot tub.
  • The introduction of chlorine will remove any bacteria.
  • Chlorine does not remove scale, only simplesilver™ will do this.

Note - Depending on the amount of scale within the system, this process may need to be completed more than once.

Filter Maintenance

  • It is very important that the filters are cleaned at least every two weeks. A filter sanitising solution must be used to remove the contaminates, as water alone cannot remove these. Your hot tub retailer will be able to assist you in product selection.
  • Make sure these are dry before reintroducing as the filter fibres will expand making these more effective.
  • Dry filters also stops the water from foaming.
  • Filters generally have a life of about 12 months after which they will saturate, you will be unable to clean these further & they will be ineffective. At this point they will need to be replaced.

The water has - a green tinge - is not crystal clear - has an odour

As a reference, your hot tub water "Should Always Look Like This" when using simplesilver™.

The water has -

  • A green tinge & is not crystal clear
  • Translucent snowflake looking things in it
  • Things that look like shredded tissue paper in it
  • A yellow-pink slime all over the filter & in the filter bay

Check the following settings

  • In the majority of cases this is due to an insufficient flow of water over the simplesilver™ tablet. Are you confident the filter pump has been set correctly to circulate 100,000 litres per day?
  • This flow rate is critical as it releases the correct amount of simplesilver™ minerals at a constant & controlled rate to balance the hot tub water. If not, the water will not be pristine. Click here, "Controller Settings" for more information.
  • Filters play a critical role, are the filters blocked? If so, this restricts the water flow & limits the correct amount of simplesilver™ minerals that are released into the water to balance it.
  • To find out more click here, "How do I test if my filters are blocked" & "Why do I need to clean my filters & why are these vitally important".
  • If Bromine was previously used, then the water needs to be drained prior to starting Step 1 - Installation Process "click here for Getting Started Information".

Other important settings to check

  • Is the filter pump controller set on automatic mode?
  • Is the sleep mode turned off?
  • Is the holiday mode turned off?
  • Is the power saving mode turned off?
  • Are all jet nozzles fully open & if you have one, is there a small amount of water circulating out of the fountain?
  • Is the filter box flap opening fully & not restricting the water when the filter circulation pump operates?

If any of the above settings were incorrect & have now been adjusted

  • It will take 3 days for the water to be correctly balanced & the issues resolved.
  • Do not use the hot tub over this period.
  • After day 3, if the water is pristine - enjoy the hot tub, no further action is needed.
  • If not, follow the instructions below.

Once you are confident the settings are correct - It will be a bacteria or fungus issue

Note - On rare occasions your hot tub water may have algae or another form of bacteria or fungus that has propagated to high levels of concentration.

So what's caused this?

  • The bacteria or fungus could have originated after factory testing
  • During the shipping & freight process from the manufacturer or retailer
  • The hot tub having been left empty for long periods
  • Substandard maintenance or incorrect water management.
  • Environmental conditions
Note - The environment also has a significant impact with hot tub water. These bacteria or fungus could have come from the surrounding gardens, garden soil, the hose or nearby earthworks.

Now Follow - Solution 2 - Bacteria & Fungus Cleaning Process

For a printable version click here: Solution 2 - Bacteria & Fungus Cleaning Process

Cleaning Process

  1. Make sure the hot tub is full of water. Do not drain the water even if the water is cloudy, green or has other contaminates in it - it is not necessary.
  2. Leave the simplesilver™ tablet & the filters in the water, do not remove these.
  3. Open all jets, nozzles & water features.
  4. Purchase 5 litres of liquid chlorine from your local hardware or hot tub store. This composition of chlorine has the correct concentration level to eradicate the bacteria or fungus in the hot tub.
  5. Note: Liquid chlorine when added to water, has a pH of 13 (alkaline) & makes hypochlorous acid, the killing form of chlorine. Using trichlor (chlorine granules) lowers the pH & alkalinity, making the water acidic. This can cause damage to the equipment & hot tub - do not use this.
  6. Add the 5 litres of liquid chlorine into the hot tub water & operate all pumps for 1 hour so the water & chlorine is circulated throughout the system. Note - you will need to manually activate the pumps that have an auto-off function over this period to ensure that there is a continuous water flow.
  7. Clean the sides & underside of the hot tub cover, as well as the folding seams using the chlorinated water. Then rinse off with clean water.
  8. Remove & clean the headrests using the chlorinated water.
  9. After completing the cleaning process for 1 hour & while the hot tub is still filled with water & the pumps are off, remove the filters & with a soft cloth, use the chlorinated water from the hot tub to clean inside the filter cavity & housing area. Then clean around the water line & other areas that are out of the water to remove any bacteria or fungus.
  10. Note - your filters will have been cleaned during the cleaning process.
  11. Reinstall the filters.
  12. Drain the hot tub water.

Re-filling Process

  1. To prevent any further transfer or introduction of bacteria or fungus from the garden or surrounding areas, use a clean cloth with some bleach & wipe the end of the hose. Then turn the hose tap on & let the water run for 30 seconds before refilling the hot tub.
  2. Refill the hot tub to the recommended water level.
  3. Remove the simplesilver™ tablet from the hot tub.
  4. You need to remove the simplesilver™ bag that contains the minerals from inside the plastic tablet, as the simplesilver™ minerals may have stuck together during the cleaning process. The easiest way is to use a blunt knife & carefully prise the back off the plastic tablet. Then remove the simplesilver™ bag, taking care not to tear this.
  5. Put the bag in the hot tub water & gently massage it to break up any minerals that may have stuck together.
  6. Then gently squeeze the bag to expel any entrapped air, this will stop the tablet floating. With the bag still under water, carefully reinsert it back into the plastic tablet container & reattach the back cover.
  7. Place the simplesilver™ tablet back into your preferred location in the hot tub water.
  8. Set the filtration timer on the controller. Go to the "Controller Settings" section & follow the instructions for your model controller.
  9. Make sure you have your controller setup to circulate 100,000 litres of water daily.
  10. Ensure that you have the filter pump set on automatic mode, not sleep, holiday or power saving modes.
  11. If the simplesilver™ tablet is located in the filter bay, make sure that the water flap opens completely & that the tablet is not inhibiting this operation as it will restrict the volume of circulating water. Also ensure that all jets & nozzles are fully open.
  12. Do not use the hot tub for 5 days.
  13. If you use the hot tub before this, there will not be sufficient simplesilver™ minerals released into the water to balance it.
  14. This is due to simplesilver™ minerals being released daily into the water at a constant & controlled rate.
  15. Remember to add a small amount of chlorine after use to comply with local & government guidelines to control the bacterial levels.

Filter Maintenance

  • It is very important that the filters are cleaned at least every two weeks. A filter sanitising solution must be used to remove the contaminates, as water alone cannot remove these. Your hot tub retailer will be able to assist you in product selection.
  • Make sure these are dry before reintroducing as the filter fibres will expand making these more effective.
  • Dry filters also stops the water from foaming.
  • Filters generally have a life of about 12 months after which they will saturate, you will be unable to clean these further & they will be ineffective. At this point they will need to be replaced.

Due to a large number of people bathing continuously in a small volume of water, there will be an excess of skin, perspiration, oils, lotions, hair, water salts, dust, dirt & other foreign matter that has built up in the water, making it cloudy.

  • After heavy use & the water is not pristine, we recommend operating all jets as many times as possible.
  • This process quickly removes the contamination from the water instead of waiting for the next filter cycle.
  • The contamination is then removed from the water into the filters.
  • Depending on the amount of contamination, the filters may need to be cleaned daily until the water is returned to a pristine condition.
  • The filters must be cleaned with a filter sanitising solution, as water alone is ineffective.
  • While the filters are removed, with a cloth & container of water (to rinse the cloth), wipe the insides of the filter cavity & housing area.
  • This area is commonly overlooked & can be a cause of unpleasant odours & slippery feeling sides.
  • Make sure the filters are dry before reintroducing these as the filter fibres will expand making these more effective.
  • Dry filters also stops the water from foaming.
  • Then after reintroducing the clean filters into the water, we recommend adding a small amount of chlorine.
  • This would suggest that the hot tub water is saturated with skin contaminates.
  • Draining the water & cleaning the filters will not resolve this issue quickly due to the high level of saturation.
  • To make the cleaning process quick & simple, go to our Troubleshooting Section 3.2 & follow this process "Solution 2" .
  • This suggests that there is an excessive amount of water flowing during the filter pump cycle.
  • Over filtering can have an adverse effect on hot tub water, causing issues with clarity & water balance.
  • Make sure you have your filter pump controller setup to circulate 100,000 litres of water daily.
  • Please see the section on "Controller Settings"
  1. If you have what looks like shredded tissue paper in the water, it would indicate the presence of white tissue mold, a fungus within the water. It is not harmful to humans, but is unsightly & can clog equipment.
  2. Or if you have a yellow-pink slime in the filter, this is a naturally occurring bacteria that you sometimes get in the bathroom & is not a form of algae. It is animal not vegetable & these airborne bacteria can come from any number of naturally occurring sources.
  • Both these issues may have arisen from a previous lack of water maintenance, the garden hose or your garden surroundings.
  • To eradicate this & make the cleaning process quick & simple, go to our Troubleshooting Section 3.2 & follow this process "Solution 2"
  • Best practice is to always run the garden hose for a minute prior to topping up the water level & wipe the end of the hose with bleach, as this can be a source of the fungus.
  • "I have to compliment you on this product. I bought one hoping it would work as it sounded just so simple, almost too good to be true. However, I am about to buy my third and I just cannot praise Simplesilver highly enough. It is simple, it is effective and a pleasure to soak in my hot tub knowing I'm not absorbing nasty chemicals. Thank you. "
    - Sue W
  • "I’m a pharmacist so I know about chemicals. I used to throw in so many different chemicals into our hot tub, trying to get the right balance, but we’d still end up bathing in a chemical soup. With simplesilver™ you just chuck it in forget about it, the hot tub water’s always crystal clear and it doesn’t smell - it's just absolutely the best thing ever!"
    - Yvette Urlich
  • "We purchased a new hot tub and selected a non-chlorine water treatment product (not simplesilver™). After two months of mucking about, water the colour of milk and not getting any better, we had had enough and changed to simplesilver™. It’s been two months now and the hot tub water is as clear as the day we put it in. It’s the best product on the market for hot tubs, so simple! No testing, no chemicals, not having to put in a quick fix each week, anyone that does not use simplesilver™ is clearly mad!! My Saturday task is to clean the filter and replace it with the spare I had cleaned from the previous week, all of 10 minutes, brilliant! Its a fantastic product and worth every cent. Update October 2019 - Just letting you know I am still using simplesilver, must be about 5 years now and have never ever had any problems and the hot tub is still running the same as it was when new. Once again a fantastic product!!"
    - Bruce
  • "I developed a skin thing using the other stuff - chlorine, bromine. I came up with blisters, itching. I tried a range of chemical options but found in the end that nothing solved my problem, until I discovered a fellow sufferer whose skin irritation problems were solved by replacing all the chemicals in his hot tub with simplesilver™. I bought it and sure enough, it was fine. I’ve been able to get back into the hot tub again with no reaction. I’m nothing but pleased with simplesilver™."
    - Paul Mcleod
  • "My skin is really wrecked and sensitive. I used to get skin irritations from the chemicals like chlorine but since I’ve used simplesilver™ I can go into our hot tub and get no side-effects. I Like the fact that you can put in the simplesilver™ tablet and that's it - that's all you have had to do. It’s so simple! You don’t do pH up and pH down and all that. You don’t do anything with simplesilver™ - it just goes on and on and on. We’ve used simplesilver™ for about nine years. I would absolutely recommend it to other people."
    - Zelda Sayers
  • "We have used simplesilver™ in our hot tub for about 12 years and find it amazing!! My husband has very sensitive skin that reacts with traditional chemicals so using simplesilver™ is a real benefit as he can enjoy the hot tub without any side effects. We have told various friends with tubs, all have purchased simplesilver™ and have had the same amazing experiences!!"
    - Bronwyn Steers
  • "We used other chemicals for a while but with simplesilver™ you don’t have to worry about testing the water every day. I like the ease and simplicity of it. Also I like sitting in the hot tub and not having to breathe chemical fumes - and I like the feel of the water with simplesilver™ – it kind of feels soft. I’m very happy with it simplesilver™ and I would absolutely recommend it to everybody."
    - Brenda Fleming
  • "We didn’t like the chlorine. We didn’t like have to deal with them all the time and we didn’t like smelling of chlorine. This simplesilver™ is the easy option – and we don’t have to go and shower after a swim. It’s fantastic stuff. We’ve used it for about eight years and we’ve recommended it to several people. It’s brilliant because we don’t have to do anything and we don’t smell of chlorine after we’ve been in the hot tub. And the hot tub is mint - no effect - just like new. All piping and everything is all working just like new. We’ve never had to do a thing to it. simplesilver™ is just brilliant!"
    - Mrs Green
  • "I have to compliment you on this product. I bought one hoping it would work as it sounded just so simple, almost too good to be true. However, I am about to buy my third and I just cannot praise Simplesilver highly enough. It is simple, it is effective and a pleasure to soak in my spa pool knowing I'm not absorbing nasty chemicals. Thank you. "
    - Sue W
  • "I’m a pharmacist so I know about chemicals. I used to throw in so many different chemicals into our spa pool, trying to get the right balance, but we’d still end up bathing in a chemical soup. With simplesilver™ you just chuck it in forget about it, the spa pool water’s always crystal clear and it doesn’t smell - it's just absolutely the best thing ever!"
    - Yvette Urlich
  • "We purchased a new spa pool and selected a non-chlorine water treatment product (not simplesilver™). After two months of mucking about, water the colour of milk and not getting any better, we had had enough and changed to simplesilver™. It’s been two months now and the spa pool water is as clear as the day we put it in. It’s the best product on the market for spa pools, so simple! No testing, no chemicals, not having to put in a quick fix each week, anyone that does not use simplesilver™ is clearly mad!! My Saturday task is to clean the filter and replace it with the spare I had cleaned from the previous week, all of 10 minutes, brilliant! Its a fantastic product and worth every cent. Update October 2019 - Just letting you know I am still using simplesilver, must be about 5 years now and have never ever had any problems and the spa pool is still running the same as it was when new. Once again a fantastic product!!"
    - Bruce
  • "I developed a skin thing using the other stuff - chlorine, bromine. I came up with blisters, itching. I tried a range of chemical options but found in the end that nothing solved my problem, until I discovered a fellow sufferer whose skin irritation problems were solved by replacing all the chemicals in his spa pool with simplesilver™. I bought it and sure enough, it was fine. I’ve been able to get back into the spa pool again with no reaction. I’m nothing but pleased with simplesilver™."
    - Paul Mcleod
  • "My skin is really wrecked and sensitive. I used to get skin irritations from the chemicals like chlorine but since I’ve used simplesilver™ I can go into our spa pool and get no side-effects. I Like the fact that you can put in the simplesilver™ tablet and that's it - that's all you have had to do. It’s so simple! You don’t do pH up and pH down and all that. You don’t do anything with simplesilver™ - it just goes on and on and on. We’ve used simplesilver™ for about nine years. I would absolutely recommend it to other people."
    - Zelda Sayers
  • "We have used simplesilver™ in our spa pool for about 12 years and find it amazing!! My husband has very sensitive skin that reacts with traditional chemicals so using simplesilver™ is a real benefit as he can enjoy the spa pool without any side effects. We have told various friends with tubs, all have purchased simplesilver™ and have had the same amazing experiences!!"
    - Bronwyn Steers
  • "We used other chemicals for a while but with simplesilver™ you don’t have to worry about testing the water every day. I like the ease and simplicity of it. Also I like sitting in the spa pool and not having to breathe chemical fumes - and I like the feel of the water with simplesilver™ – it kind of feels soft. I’m very happy with it simplesilver™ and I would absolutely recommend it to everybody."
    - Brenda Fleming
  • "We didn’t like the chlorine. We didn’t like have to deal with them all the time and we didn’t like smelling of chlorine. This simplesilver™ is the easy option – and we don’t have to go and shower after a swim. It’s fantastic stuff. We’ve used it for about eight years and we’ve recommended it to several people. It’s brilliant because we don’t have to do anything and we don’t smell of chlorine after we’ve been in the spa pool. And the spa pool is mint - no effect - just like new. All piping and everything is all working just like new. We’ve never had to do a thing to it. simplesilver™ is just brilliant!"
    - Mrs Green
60 day money back
Guaranteed
If simplesilver™ doesn’t clear your hot tub, contact us within 60 days from purchase and we’ll give you your money back.
60 day money back
Guaranteed
If simplesilver™ doesn’t clear your spa pool, contact us within 60 days from purchase and we’ll give you your money back.
© Copyright 2024 simplesilver™. All rights reserved
Note: simplesilver™ is for domestic hot tub use.
Not for commercial applications.
© Copyright 2024 simplesilver™. All rights reserved
Note: simplesilver™ is for domestic spa pool use.
Not for commercial applications.