Controller Settings

Set the filter pump operating times to circulate 100,000 litres of water per day - this is critical!

This ensures that the correct amount of simplesilver™ minerals are released into the water at a constant controlled rate to effectively balance the pH, alkalinity, total dissolved solids, scale, corrosion & bacterial levels.
It is also vitally important that this volume of water can be passed through the filters. This filtration water volume ensures that any skin, perspiration, oils, lotions, hair, water salts, dust, dirt & other foreign matter are removed from the water.
This process ensures that the water condition & clarity is maintained.

Find your spa pool controller & set-up process from the list below

If you don't see your spa pool controller listed below?
Don't have the spa pool manual?
Or you don't know the filter pump flow rate or need to understand how to calculate this, "click here for assistance"

Alpine spas

Balboa VS/GS5xxSZ Controller

All models need to operate the filter cycle pump for a total of 8 hour per day. If your controller has one filter cycle period set this for 8 hours.

Press Warm or Cool button, then Jets1 button.
Then press the Warm or Cool button again to adjust the time to 8 hours.
Press Jets1 button to exit the programming mode.

Balboa VS/GS5 xxD Controller

The filter pump needs to operate for a total of 8 hours per day. This controller will operate the filter pump for two periods of 4 hours over a 24 hour period.

Press Time button.
The press the Mode/Prog button.
Press again the Model/Prog within 3 seconds.
Set Start Filter 1 will appear.
Press Up or Down button to to set the start time.
Then press the Mode/Prog button again to set Stop Filter 1 & then set the stop time. These start & stop times needs to have a 4 hour duration.
Complete the same process again to set the second start & stop period for the second 4 hour duration. This will say Set Start Filter 2 & Set Stop Filter 2.

AquaSpring

SP 601 Controller

All fitted with 24 hour filter circulation pumps, leave in this mode.

Cal Spas

All Models

Models with 2 hp filter pumps need to be set on 6 hours per day.

Models with 5 hp filter pumps need to be set on 5 hours per day.

Models with 24 hour circulation filter pumps, no change needed, leave in this mode.

Cedar Wood Tubs

All Models

Set time clock on 10 hours per day.

Eco Value Spas

Microsilk 700 & 1200

All models are fitted with 24 hour filter circulation pumps, leave in this mode. The models listed below need to be set on;

Microsilk 1200 will need to be set on F4.
Mircosilk 700 will need to be set on F4.

Balboa VS/GS5xxZ Controller

The filter pump needs to operate for 8 hours per day. How to change:

Press Temp button then the Jets button.
Press Temp button to adjust to F4. This will operate the filter pump for two periods of 4 hours over a 24 hour period.
Press Jets button to exit the programming mode.

Balboa VS/GS5xxSZ Controller

All models need to operate the filter cycle pump for a total of 8 hour per day. If your controller has one filter cycle period set this for 8 hours.

Press Warm or Cool button, then Jets1 button.
Then press the Warm or Cool button again to adjust the time to 8 hours.
Press Jets1 button to exit the programming mode.

The filter pump needs to operate for 8 hours per day.

Balboa VS/GS5 xxD Controller

The filter pump needs to operate for a total of 8 hours per day. This controller will operate the filter pump for two periods of 4 hours over a 24 hour period.

Press Time button.
The press the Mode/Prog button.
Press again the Model/Prog within 3 seconds.
Set Start Filter 1 will appear.
Press Up or Down button to to set the start time.
Then press the Mode/Prog button again to set Stop Filter 1 & then set the stop time. These start & stop times needs to have a 4 hour duration.
Complete the same process again to set the second start & stop period for the second 4 hour duration. This will say Set Start Filter 2 & Set Stop Filter 2.

Fisher Spas

All models

All models set on 12 hours per day.

Balboa VS/GS5xxZ Controller

The filter pump needs to operate for 8 hours per day. How to change:

Press Temp button then the Jets button.
Press Temp button to adjust to F4. This will operate the filter pump for two periods of 4 hours over a 24 hour period.
Press Jets button to exit the programming mode.

Galaxy Spas

SpaNet Controller

How to change: There are two steps to set the filter pump timer. One:

Set up the filter pump to operate for a total of 12 hours per day.

Press & hold both the up &down arrow buttons. This is the main menu.
Then press either the up or the down arrow buttons until you find FILT. This is the filter pump timer setting menu.
Press OK.
Again press either the up or the down arrow buttons to adjust the filtration time, set this to 12 hours.
Then press OK to set this & exit the menu.

Two:

Then set up the time periods or time-slots for the filter pump to operate over a 24 hour period.

You then need to set the periods or time-slots for the 12 hours of filtering over a 24 hours period. The options available are to select the filtration pump to operate every 1, 2, 3, 4, 5, 8, 12 or 24 hours. The controller will automatically calculate the time-slots required to operate the filter to achieve a total of 12 hours. For example, if you set this to 1, then the controller will set the pump to operate for 1/2 an hour every hour over a 24 hour period so the filter pump operates for 12 hours in total.
Press & hold both the up & down arrow buttons. This is the main menu.
Then press either the up or the down arrow buttons until you find F.CYC (filtration periods or time-slots). This is the filter pump cycle time-slot setting menu as outlined in 1 above.
Press OK.
Again press either the up or the down arrow buttons to adjust the filtration period or time-slot, set this to 3. The controller will then operate the filter pump for 3 times over 24 hours. Each time-slot will have a duration of 4 hours totaling 12 hours per day.
Then press OK to set this & exit the menu.

Note: Make sure the sleep timer is set to OFF as this will interrupt the 12 hours of filtering. You will need to refer to your manual to do this.

SpaTech Controller

Set up the filter pumps to operate for a total of 12 hours per day

Select time, then mode.
The filter 1 start time appears on the screen.
Select the hour by pressing the warm or cool button then press mode to enter.
Filter 1 end time appears on the screen. Press the warm or cool button to set the filter end time for 1^st filter cycle.
Press mode to exit the 1^st filter cycle & enter the 2^nd filter cycle setting.
Select hour by pressing warm or cool to set the start time of the 2^nd filter cycle setting then press mode.
Then press warm or cool to set the filter 2 end time. Press mode to exit programming.

Gecko - in.k1001 - in.k330 -in.k806 Controllers

Leave all models in default mode for the filter pump circulation time.

Hotspot

All Models

Set the filter pump on for 6 hours per day. How to change the controller:

Press the SET button until the TOOLS menu is illustrated.
Then press the TEMP + button to enter the TOOLS sub-menu.
Press the SET button until FILT1 or FILT2 is illuminated on the display.
Then press the TEMP + button to enter FILT1 or FILT2. The F1 or F2 icon will flash to tell you which filter cycle you are in.
Using the Temp + or the Temp - buttons adjust to the desired filter cycle time. Set one cycle for 6 hours or two cycles for 3 hours each.

Hotsprings

Lime Light Series

NOTE: ISSUES WITH THIS SPA POOL

Hotspring spa pools have small 24 hour filter circulation pumps. Unfortunately these pumps do not circulate enough water to distribute the correct quantity of simplesilver ingredients into the water to balance it.

Should you still wish to use simplesilver to balance the pH, alkalinity, scale & corrosion, you must use a small amount of chlorine daily (about a teaspoon) to control the of bacterial levels.

Alternatively you would need to manually operate the larger massage jet pump at least once a day to get the correct volume of water flowing over the simplesilver tablet. Or have your electrician fit a simple time clock to operate this pump daily.

Otherwise take the simplesilver tablet & packaging back within 60 days & receive a full refund.

High Life Series

NOTE: ISSUES WITH THIS SPA POOL

Should you still wish to use simplesilver to balance the pH, alkalinity, scale & corrosion, you must use a small amount of chlorine daily (about a teaspoon) to control the of bacterial levels.

Otherwise take the simplesilver tablet & packaging back within 60 days & receive a full refund.

Just Spas

All Models

The filter pump need to be set for a total of 8 hours per day. Set the two filter cycles to 4 hours each per day.

Kiwi spas

All Models

For all models, set the filter circulation pump timer, to operate for 8 hours per day.

Lay-Z-Spa

All Models

Lay-Z-Spas have small 24 hour filter circulation pumps. Unfortunately these pumps do not circulate enough water to distribute the correct quantity of simplesilver ingredients into the water to balance it.

Should you still wish to use simplesilver to balance the pH, alkalinity, scale & corrosion, you must use a small amount of chlorine daily (about a teaspoon) to control the of bacterial levels.

Otherwise take the simplesilver tablet & packaging back within 60 days & receive a full refund.

Leisurerite Spas

Balboa VS/GS5xxZ Controller

The filter pump needs to operate for 8 hours per day.

How to change:

Press Temp button then the Jets button.
Press Temp button to adjust to F4. This will operate the filter pump for two periods of 4 hours over a 24 hour period.
Press Jets button to exit the programming mode.

Balboa VS/GS5 xxD Controller

The filter pump needs to operate for a total of 8 hours per day. This controller will operate the filter pump for two periods of 4 hours over a 24 hour period.

Press Time button.
The press the Mode/Prog button.
Press again the Model/Prog within 3 seconds.
Set Start Filter 1 will appear.
Press Up or Down button to to set the start time.
Then press the Mode/Prog button again to set Stop Filter 1 & then set the stop time. These start & stop times needs to have a 4 hour duration.
Complete the same process again to set the second start & stop period for the second 4 hour duration. This will say Set Start Filter 2 & Set Stop Filter 2.

Moana Spas

Balboa GS100 Controller

The circulation filter pump needs to operate for a total of 8 hour per day.

Your controller has two pre-programmed filter pump periods which are both set for 1 hour each. These need to be changed to 4 hours for each period, the cycles start at 12 hour intervals. The first cycle starts after the filter period is set up.

Press Warm button, then the Jet button to enter the programming mode.
Then press the temp up or temp down buttons again to adjust the time to 4 hours.
Press Jets button to exit the programming mode.

Make sure the the controller is in Standard Mode (ST), not economy (EC) or Sleep (SL) modes.

Balboa GS510 Controller

The circulation filter pump needs to operate for a total of 8 hour per day.

Press Warm or Cool buttons, then the Jet 1 button to enter the programming mode.
Then press the Cool or Warm buttons again to adjust the time to 4 hours.
Press Jet 1 button to exit the programming mode.

Make sure the the controller is in Standard Mode (ST), not economy (EC) or Sleep (SL) modes.

Balboa BP601 Controller

The circulation filter pump needs to operate for a total of 8 hour per day.

Your controller has two filter pump periods which the default times are both set for 2 hour each. These need to be changed to 4 hours for each period. Otherwise the second filter cycle can be disabled & the first cycle period set for 8 hours.

Press & hold the Temp button until this flashes to enter the programming mode.
Then press the Light button repeatedly until FLTR1 appears.
Press the Temp button twice, the start time will show & the hour will flash.
Then press the Temp button repeatedly to set the start hour. Then press the Light button to set the minutes, the press the Temp button to confirm the set start time.
Press the Light button, then press the Temp button, FLTR 1 will appear & show the length in hours & this will flash. Press the Temp button repeatedly to adjust the time to 4 hours.
Then press the Light button 3 times, FLTR 2 will appear in the display. Press the Temp button, then the Light button, then press the Temp button again, the second start cycle time will flash.
Press the Temp button repeatedly to set the start hour.
Then Light button, then press the Temp button, FLTR 2 will appear & show the length in hours & this will flash. Press the Temp button repeatedly to adjust the time to 4 hours.
Wait 30 seconds to go back to the main screen.

Make sure the controller is in Ready Mode & not Rest mode.

MSpa

All Models

MSpa spa pools have small 24 hour filter circulation pumps. Unfortunately these pumps do not circulate enough water to distribute the correct quantity of simplesilver ingredients into the water to balance it.

Should you still wish to use simplesilver to balance the pH, alkalinity, scale & corrosion, you must use a small amount of chlorine daily (about a teaspoon) to control the of bacterial levels.

Otherwise take the simplesilver tablet & packaging back within 60 days &receive a full refund.

Paradise Hot Tubs

SpaNet SV Mini-1

Set on 10 hours per day.

How to change:

Press both the UP & DOWN arrow buttons at the same time. This will access the main menu.
Then press either the UP or the DOWN arrow buttons until you get to FILT, then press OK. This is takes you to the filtration time setting menu.
Again, press either the UP or the DOWN arrow buttons until you have 10, this sets the filter pump for 10 hours of filtration.
Then press OK.
Press the UP or the DOWN arrow buttons again to scroll to EXIT then press OK all done.

Plug in Spa

SP 601 Controller

Set the filter pump on for 15 minutes per hour.

If fitted with an air button control-add time clock to pump, set on 5-6 hours per day with a 1 hp filter pump.

How to change

Press the Down & the Air buttons simultaneously.
Then release the buttons once it displays F.00-15
Then press & hold the Up button until 15 minute time period is reached, then release the button to set the hourly filter cycle.

Rotaform

SP 601 Controller

Set the filter pump to operate 15 minutes per hour.

How to change:

Press Down & the Air button simultaneously.
Release once to put the controller into filter pump set mode.
Hold Up button until F.00-15. is displayed, then release to the button to set.

Spa Sensations

SP 800 Controller

Set on 25 minutes per hour unless the pool is fitted with a 24 hour filter circulation pump. If its got a 24/7 circulation pump leave in this mode.

How to change:

Select the ADV. OPTIONS sub-menu from the main menu.
Then select the FILT. PERIOD menu item.
Press the SCROLL button to begin filtration time period modification.
Use the UP & DOWN buttons to set the desired filtration period of 25 minute per hour.
Press the SCROLL button to confirm the current setting & return to the ADV. OPTIONS sub-menu.

SP 601 Controller

Set on 15 minutes per hour.

How to change:

Press down & the air button simultaneously.
Then release once it say’s F. 00-15.
Then hold either the up or down buttons until the correct time of 15 minutes is reached, then release to set this time period.

Stoked Spa Pools - Wanaka

SpaNet SV

Set on 10 hours per day.

How to change:

Press both the UP & DOWN arrow buttons at the same time. This will access the main menu.

Then press either the UP or the DOWN arrow buttons until you get to FILT, then press OK. This is takes you to the filtration time setting menu.

Again, press either the UP or the DOWN arrow buttons until you have 10, this sets the filter pump for 10 hours of filtration.

Then press OK.

Press the UP or the DOWN arrow buttons again to scroll to EXIT then press OK all done.

Sundance spas

Select Series

The filter circulation pump need to be set on 8 hours per day, also set spa on standard mode F3

How to change:

Selecting the Filtration/Heating Mode.
Then press & hold both control panel WARMER (Up) & COOLER (Down) buttons at the same time, then release.
Press either WARMER (Up) or COOLER (Down) buttons to select filtration/heating mode F0-F6 or lock modes L1-L3 outlined below.

During the filtration/heating cycle the Jets Pump 1 low speed & circulation pump will activate.

680 Series

Set the spa on standard mode F3

How to change:

Select the Filtration/Heating Mode.
Press & hold both control panel WARMER (+ ) & COOLER (- ) buttons at the same time, then release.
Then press either WARMER (+ ) or COOLER (- ) buttons to select filtration/heating mode F1-F6 or lock modes.

780 Series

Leave circulation pump set on 8 hours per day (unless it’s a Dover model then please leave on 24 hours), also set spa on standard mode F3

How to change:

Select the Filtration/Heating Mode
Press & hold both control panel WARMER (Up ) & COOLER (Down ) buttons simultaneously, then release.
Press either the WARMER (Up ) or COOLER (Down ) buttons to select filtration/heating mode F0-F6 or lock modes L1-L3 outlined below.
During the filtration/heating cycle the Jets pump 1 will operate on low speed.

880 Series

Set the filter circulation pump on 15 hours

How to change:

The LCD screen will display Circ. The system is then ready to accept your changes.

Press the (SELECT) button once. The previously programmed start time appears on the LCD display.
Then press either the (UP) or (DOWN) buttons to adjust the start time in 30-minute increments.
Press the (SELECT) button to program the daily filter pump duration.
Press either the (UP) or (DOWN) buttons to program the duration time in 1 hour increments, set the time to 15 hours.
Then press the (DISPLAY) button to save changes, this will then revert back to the water temperature display.

The Spa and Pool Factory

SpaNet Controller

Set on 4 hours per day unless you have a 2015 Gem or Geisha which need's to be set on 5 hours.

How to change:

Press & hold up & down buttons simultaneously.
Then press the up or down button until you find FILT is displayed.
Press OK button.
Use up or the down buttons to adjust filtration time, either 4 or 5 hours dependent on controller model above.
Press OK to set the time.

Trueform

SpaNet SV Mini-1

Set on 10 hours per day.

How to change:

Press both the UP & DOWN arrow buttons at the same time. This will access the main menu.
Then press either the UP or the DOWN arrow buttons until you get to FILT, then press OK. This is takes you to the filtration time setting menu.
Again, press either the UP or the DOWN arrow buttons until you have 10, this sets the filter pump for 10 hours of filtration.
Then press OK.
Press the UP or the DOWN arrow buttons again to scroll to EXIT then press OK all done.

SP 800 Controller

Set on 25 minutes per hour unless fitted with a 24 hour circulation filter pump. If you have a 24/7 filter pump leave in this mode.

How to change:

Select the ADV. OPTIONS sub-menu from the main menu.
Then select the FILT. TIME menu.
Press the SCROLL button to begin filtration time modification.
Use the UP & DOWN buttons to set the filtration time period of 25 minutes per hour.
Then press the SCROLL button to confirm the current filter pump time setting & return to the ADV. OPTIONS sub-menu.

SP 601 Controller (red digital temperature display)

Set on 15 minutes per hour. If you have upgraded to a 3hp, two speed pump, then you need to set this set on F13

How to change:

Press the down & the air button simultaneously.
Then release once it say’s F.00-15
Press & hold the up button until time of 15 minutes is reached, then release to set this filter pump operation per hour.
Now press the down arrow & the pump button simultaneously, Ht.F or Ht.d will show in the display. The display needs to show Ht.F
To change the display to Ht.F, press the up arrow button & once this is displayed, release the button. Your spa is now set to run for 15 mins per hour.

Topmaq

All Models

All models are fitted with 24 hour circulation pumps, leave in this mode.

Vortex Spas

SpaNet SV 3-4 Controller

For electrically heated pools, set the filtration pump to operate for 12 hours per day.

If a heat pump is installed, set the filter pump to operate for 16 hours per day & make sure to set the controller to standard mode. Please remove the Purezone filter & replace with a standard cartridge filter.

How to change:

Press & hold the up & down buttons simultaneously.
Then press either the up or down buttons until you find FILT.
Press OK.
Then press either the up or down buttons to adjust the filtration time to either 12 or 16 hours as outlined above.
Press OK to set the filter time period.

Wanaka Spring Spas

All Models

All models have 24 hour filter circulation pumps, leave in this mode.

"I have to compliment you on this product. I bought one hoping it would work as it sounded just so simple, almost too good to be true. However, I am about to buy my third and I just cannot praise Simplesilver highly enough. It is simple, it is effective and a pleasure to soak in my hot tub knowing I'm not absorbing nasty chemicals. Thank you. "
- Sue W
"I’m a pharmacist so I know about chemicals. I used to throw in so many different chemicals into our hot tub, trying to get the right balance, but we’d still end up bathing in a chemical soup. With simplesilver™ you just chuck it in forget about it, the hot tub water’s always crystal clear and it doesn’t smell - it's just absolutely the best thing ever!"
- Yvette Urlich
"We purchased a new hot tub and selected a non-chlorine water treatment product (not simplesilver™). After two months of mucking about, water the colour of milk and not getting any better, we had had enough and changed to simplesilver™. It’s been two months now and the hot tub water is as clear as the day we put it in. It’s the best product on the market for hot tubs, so simple! No testing, no chemicals, not having to put in a quick fix each week, anyone that does not use simplesilver™ is clearly mad!! My Saturday task is to clean the filter and replace it with the spare I had cleaned from the previous week, all of 10 minutes, brilliant! Its a fantastic product and worth every cent. Update October 2019 - Just letting you know I am still using simplesilver, must be about 5 years now and have never ever had any problems and the hot tub is still running the same as it was when new. Once again a fantastic product!!"
- Bruce
"I developed a skin thing using the other stuff - chlorine, bromine. I came up with blisters, itching. I tried a range of chemical options but found in the end that nothing solved my problem, until I discovered a fellow sufferer whose skin irritation problems were solved by replacing all the chemicals in his hot tub with simplesilver™. I bought it and sure enough, it was fine. I’ve been able to get back into the hot tub again with no reaction. I’m nothing but pleased with simplesilver™."
- Paul Mcleod
"My skin is really wrecked and sensitive. I used to get skin irritations from the chemicals like chlorine but since I’ve used simplesilver™ I can go into our hot tub and get no side-effects. I Like the fact that you can put in the simplesilver™ tablet and that's it - that's all you have had to do. It’s so simple! You don’t do pH up and pH down and all that. You don’t do anything with simplesilver™ - it just goes on and on and on. We’ve used simplesilver™ for about nine years. I would absolutely recommend it to other people."
- Zelda Sayers
"We have used simplesilver™ in our hot tub for about 12 years and find it amazing!! My husband has very sensitive skin that reacts with traditional chemicals so using simplesilver™ is a real benefit as he can enjoy the hot tub without any side effects. We have told various friends with tubs, all have purchased simplesilver™ and have had the same amazing experiences!!"
- Bronwyn Steers
"We used other chemicals for a while but with simplesilver™ you don’t have to worry about testing the water every day. I like the ease and simplicity of it. Also I like sitting in the hot tub and not having to breathe chemical fumes - and I like the feel of the water with simplesilver™ – it kind of feels soft. I’m very happy with it simplesilver™ and I would absolutely recommend it to everybody."
- Brenda Fleming
"We didn’t like the chlorine. We didn’t like have to deal with them all the time and we didn’t like smelling of chlorine. This simplesilver™ is the easy option – and we don’t have to go and shower after a swim. It’s fantastic stuff. We’ve used it for about eight years and we’ve recommended it to several people. It’s brilliant because we don’t have to do anything and we don’t smell of chlorine after we’ve been in the hot tub. And the hot tub is mint - no effect - just like new. All piping and everything is all working just like new. We’ve never had to do a thing to it. simplesilver™ is just brilliant!"
- Mrs Green

"I have to compliment you on this product. I bought one hoping it would work as it sounded just so simple, almost too good to be true. However, I am about to buy my third and I just cannot praise Simplesilver highly enough. It is simple, it is effective and a pleasure to soak in my spa pool knowing I'm not absorbing nasty chemicals. Thank you. "
- Sue W
"I’m a pharmacist so I know about chemicals. I used to throw in so many different chemicals into our spa pool, trying to get the right balance, but we’d still end up bathing in a chemical soup. With simplesilver™ you just chuck it in forget about it, the spa pool water’s always crystal clear and it doesn’t smell - it's just absolutely the best thing ever!"
- Yvette Urlich
"We purchased a new spa pool and selected a non-chlorine water treatment product (not simplesilver™). After two months of mucking about, water the colour of milk and not getting any better, we had had enough and changed to simplesilver™. It’s been two months now and the spa pool water is as clear as the day we put it in. It’s the best product on the market for spa pools, so simple! No testing, no chemicals, not having to put in a quick fix each week, anyone that does not use simplesilver™ is clearly mad!! My Saturday task is to clean the filter and replace it with the spare I had cleaned from the previous week, all of 10 minutes, brilliant! Its a fantastic product and worth every cent. Update October 2019 - Just letting you know I am still using simplesilver, must be about 5 years now and have never ever had any problems and the spa pool is still running the same as it was when new. Once again a fantastic product!!"
- Bruce
"I developed a skin thing using the other stuff - chlorine, bromine. I came up with blisters, itching. I tried a range of chemical options but found in the end that nothing solved my problem, until I discovered a fellow sufferer whose skin irritation problems were solved by replacing all the chemicals in his spa pool with simplesilver™. I bought it and sure enough, it was fine. I’ve been able to get back into the spa pool again with no reaction. I’m nothing but pleased with simplesilver™."
- Paul Mcleod
"My skin is really wrecked and sensitive. I used to get skin irritations from the chemicals like chlorine but since I’ve used simplesilver™ I can go into our spa pool and get no side-effects. I Like the fact that you can put in the simplesilver™ tablet and that's it - that's all you have had to do. It’s so simple! You don’t do pH up and pH down and all that. You don’t do anything with simplesilver™ - it just goes on and on and on. We’ve used simplesilver™ for about nine years. I would absolutely recommend it to other people."
- Zelda Sayers
"We have used simplesilver™ in our spa pool for about 12 years and find it amazing!! My husband has very sensitive skin that reacts with traditional chemicals so using simplesilver™ is a real benefit as he can enjoy the spa pool without any side effects. We have told various friends with tubs, all have purchased simplesilver™ and have had the same amazing experiences!!"
- Bronwyn Steers
"We used other chemicals for a while but with simplesilver™ you don’t have to worry about testing the water every day. I like the ease and simplicity of it. Also I like sitting in the spa pool and not having to breathe chemical fumes - and I like the feel of the water with simplesilver™ – it kind of feels soft. I’m very happy with it simplesilver™ and I would absolutely recommend it to everybody."
- Brenda Fleming
"We didn’t like the chlorine. We didn’t like have to deal with them all the time and we didn’t like smelling of chlorine. This simplesilver™ is the easy option – and we don’t have to go and shower after a swim. It’s fantastic stuff. We’ve used it for about eight years and we’ve recommended it to several people. It’s brilliant because we don’t have to do anything and we don’t smell of chlorine after we’ve been in the spa pool. And the spa pool is mint - no effect - just like new. All piping and everything is all working just like new. We’ve never had to do a thing to it. simplesilver™ is just brilliant!"
- Mrs Green